2008年6月26日 星期四

著作目錄
西文學術期刊論文

  1. Ko-Ta Chiang. Fu-Ming Chang, Nun-Ming Liu, Jenn-Tsong Horng,Experimental investigation of the cooling effect using the cold air gun coolant system in high-speed milling process ,中國機械工程學會第三十屆全國學術研討會論文集,宜蘭(2013)。
  2. Chih-Chung Chou, Nun-Ming Liu, Jenn-Tsong Horng, Ko-Ta Chiang, Designing parameter optimization of a Parallel-Plain Fin heat sink using the grey-based fuzzy algorithm with the orthogonal arrays, International Journal of Thermal Sciences, 48/ 12, (2009) 2271-2279. (SCI) (2009/12)
  3. Kuang-Yuan Kung, Jenn-Tsong Horng, Ko-Ta Chiang, Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide, International Journal of Advanced Manufacturing Technology, 40/1-2, (2009) 95-104. (SCI) (2009/1)
  4. Nun-Ming Liu, Jenn-Tsong Horng, Ko-Ta Chiang, The method of grey-fuzzylogic for optimizing multi-response problem during the manufacturing process: a case study of the light guide plate printing process, International Journal of Advanced Manufacturing Technology, 4/11-12 (2009) 200-210. (SCI) (2009/3)
  5. Jenn-Tsong Horng, Nun-Ming Liu, Ko-Ta Chiang, 2008, Investigating the Machinability evaluation in the hard turning of Hadfield steel with Al2O3/TiC mixed ceramic tool based on the response surface methodology Journal of Material Processing Technology, 208 (1-3), pp. 532-541. (SCI)
  6. Te-Chang Tsai, Jenn-Tsong Horng, Chih-Chung Chou, Ko-Ta Chiang, 2008, The effect of heterogeneous second phase on the machinability evaluation of spheroidal graphite cast irons in the WEDM process, Materials & Design, Vol.29, pp.1762-1767. (SCI)
  7. Jenn-Tsong Horng, Ko-Ta Chiang, 2008, A grey and fuzzy algorithms integrated approach to the optimization of turning Hadfield steel with Al2O3/TiC mixed ceramic tool, Journal of Material Processing Technology, Vol. 207 , September, pp.89-97. (SCI).
  8. Horng, J. T., Chang, S. F., Wu, T. Y., Chen, P. L., and Hung, Y. H., 2008, Thermal Optimal Design for Parallel Plain-Fin Heat Sinks by Using Neuro-Genetic Method, IEEE Transactions on Components and Packaging Technologies, Vol. 31, No. 2, June 2008, pp.449-460. (SCI)
  9. Chen, H. T., Chen, P. L., Horng, J. T. , and Hung, Y. H., 2005, Design Optimization for Pin-Fin Heat Sinks, ASME Journal of Electronic Packaging, Vol.127, No.4, December 2005, pp.397-406. (SCI)
  10. Chen H. T., Horng, J. T., Chen, P. L., and Hung, Y. H., 2004, Optimal Design for PPF Heat Sinks in Electronics Cooling Applications, ASME Journal of Electronic Packaging,Volume 126, Issue 4, December 2004, Pages 410-422. (SCI)
  11. Wu, T. Y., Wu, M. C., Horng, J. T., Chang, S. F., Chen, P. L. and Hung, Y. H. ,2007,」 Thermal Optimal Design for Heat Sinks or Heat Sink/TEC Assemblies in a Ducted Flow,」 International Electronic Packaging Technical Conference and Exhibition, July 8-12, Vancouver, Canada.(EI)
  12. Wu, M. C., Wu, T. Y., Horng, J. T., Chang, S. F., Chen, P. L. and Hung, Y. H. ,2007, A Semi-Empirically Thermal Optimization for Heat Sink/TEC Assemblies with Various External Thermal Resistances, International Electronic Packaging Technical Conference and Exhibition, July 8-12, Vancouver, Canada. (EI)
  13. Peng, C. H., Wu, M. C., Lee , C. Y., Horng, J. T., Fang, C. J., and Hung, Y. H., 2006, An Optimal Approach with Genetic Algorithm for Thermal Performance of Heat Sink/TEC Assembly, Itherm 2006, San Diego, CA, USA, May 30-June 2. (EI)
  14. Chen, H. T., Chen, P. L., Horng, J. T., Chang, S. F., Wu, T. Y., and Hung, Y. H., 2006, Thermal Design Optimization for Strip-Fin Heat Sinks with a Ducted Air Flow, Itherm 2006, San Diego, CA, USA, May 30-June 2. (EI)
  15. Wu, T. Y., Wang, M. P., Horng, J. T., Chang, S. F., and Hung, Y. H., 2005, Forced Convective Heat Transfer for Partially-Confined Compact PPF Heat Sinks with Top-Bypass Effect, IPACK2005-73121, Proceedings of InterPACK'05, International Electronic Packaging Technical Conference and Exhibition, San Francisco, USA, July 17-22. (EI)
  16. Wang, M. P., Chen, H. T., Horng, J. T., Wu, T. Y., Chen, P. L., and Hung, Y. H., 2005, Thermal Optimal Design for Partially-Confined Compact Heat Sinks, IPACK2005-73118, Proceedings of InterPACK'05, International Electronic Packaging Technical Conference and Exhibition, San Francisco, USA, July 17-22. (EI)
  17. Wang, M. P., Wu, T. Y., Horng, J. T., Lee, C. Y., and Hung, Y. H., 2005, Fluid Flow Characteristics for Partially-Confined Compact PPF Heat Sinks, HT2005-72225, Proceedings of HT2005, 2005 ASME Summer Heat Transfer Conference, San Francisco, USA, July 17-22. (EI)
  18. Chai, T. S., Horng, J. T., Wu, T. Y., and Hung, Y. H., 2004, Thermal Performance Measurement for Confined Heat Sinks, ITHERM 2004, Ninth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, pp.302-309, Las Vegas, NV, USA, June 1-4. (EI)
  19. Lin,Z.C. and J.T. Horng, 2000, 「Feature-Based Sheet Metal Design and Development System」, International Journal of Materials and Product Technology, Vol.15, No.6, pp.471-494.(SCI)
  20. Lin,Z.C. and J.T. Horng,1998,」 Sheet Metal Products Database in Support of their Process Planning and Surface Development」, International Journal of Computer Integrated Manufacturing, Vol.11,No.6, pp.542-533. (SCI)
  21. Lin,Z,C and J.T. Horng , 1996,」Geometric Data of the Object-Oriented Program Method and Development Rule for Thin Sheet Metal Product」, CSNE, Journal of Chinese Society of Mechanical Engineers, Vol.17,No.3,pp.213-219.
二 中文學術期刊論文
  1. 洪振聰, "使用反應曲面法與連續近似最佳法來探討Ti-6Al-4V 鈦合金之線切割放電加工性能與最佳化 [中國機械工程學會第二十九屆全國學術研討會]," , 2012.
  2. 洪振聰, "運用空氣冷卻系統於車削鈦合金過程中刀具溫度與表面粗糙度之驗證與建模分析 [中國機械工程學會第二十九屆全國學術研討會]," , 2012.
  3. 江可達,洪振聰,1999,」樹德工商專科學校二年制夜間部學生來源分析統計』,樹德學報,第二十三期, pp.225-243.
  4. 江可達,洪振聰,張福平,2001,」自然對流狀態下散熱片冷卻方式之改進』,修平學報,第三期, pp.47-65.
三 研討會論文
  1. 林榮慶,洪振聰, 『鈑金設計與展開資料庫研究』, 中國機械工程學會第十一屆學術研討會論文集,第87-94頁,台中市(1994)
四 其他著作
  1. 林榮慶,洪振聰, 『電腦輔助鈑金展開專家系統及資料庫研究』,第一年金屬工業研究中心研究計劃報告(1994).


五 產學合作
1. 林榮慶,洪振聰,‘電腦輔助鈑金展開專家系統及資料庫研究",第一年金屬工業研究中心研究計劃報告(1994)。
2. 92年, CAE-3D實體模型建構系統Solidworks套裝軟體教育版,技術服務案,2003/9/1~2004/8/31,實威科技股份有限公司。
3.心軸設計加工專家系統開發計畫,學界關懷計畫。98年4月~9月。計畫編號:pc097130756,金裕盛精密工業有限公司。
4.加工流程診斷改善計畫,學界關懷計畫。98年11月~99年4月。計畫編號:pc098130673,印瞬工業有限公司。
5. 鍛鑄件毛胚檢測技術開發計畫。99年7月~99年12月。計畫編號: 100141476,振豐機器廠股份有限公司。
6.應用反應曲面法於陶瓷刀具車削硬質鋼材加工最佳化研究,Using the response surface methodology on optimization of turning Hadfield steel with ceramic cutting tools ,:99 年 8 月 1 日至 100 年 7 月 31 日,NSC 99-2221-E-164-002,國科會計畫。
7.提升紡織纖維材料導熱率 電磁波遮蔽率輔導計畫,科技關懷計畫。100年8月~99年12月。計畫編號: PC100141476,足好有限公司。
8.CNC機械加工製程診斷計畫,科技關懷計畫。101 年 5 月  ~  101 年 10 月。計畫編號:PC101130647,東珂工業股份有限公司。
9.金屬製品手工具產業以市場導向創新研發產品價值鏈整合技術提升,科技關懷計畫。102年6月~ 102年11月。計畫編號:102PC039,金裕盛精密工業有限公司。